Appliance repair

Dishwasherrepair

What goes wrong, which part it usually is, and what moves the price.

$130 to $600Typical for the part plus the labor to fit it. The part is what sets the price, so the diagnosis comes before the figure.

The short answer

Any dishwasher repair is two jobs: finding out what broke, and the part to fix it. Most of the time the part that failed is a cheap one, so a tech checks those first.

A technician crouched at an open dishwasher, lifting the round mesh filter cup out of the floor of the stainless tub.

What usually fails

  • Will not drain, which is the drain pump, the filter or a blocked air gap
  • Not cleaning properly, usually the spray arms, the filter or a failed circulation pump
  • Leaking at the door, normally the door gasket or a worn hinge letting the door sit proud
  • Will not fill, which is the inlet valve or a frozen supply line in winter
  • Will not start, commonly the door latch switch or the control board

The part sets the price, not the appliance and not where you live. Have the model and serial number off the sticker when you call. Two machines with the same name on the door can take different parts, and the sticker is the only thing that tells us which.

Typical ranges by part

PartTypical range
Drain pumpStanding water in the base$180 to $400
Circulation or wash pumpRuns a full cycle and does not clean$250 to $550
Water inlet valveWill not fill. In winter check for a frozen supply line first$150 to $330
Door latch switchWill not start, the most common fault on the type$130 to $300
Door gasket or hingeLeaking at the door, or a door that sits proud$150 to $380
Heating elementNot drying, or not reaching sanitizing temperature$170 to $380
Control boardUnresponsive panel where the latch switch has been ruled out$300 to $600

For comparison, a replacement typically runs $700 to $1,600 installed, which is the figure to compare against rather than the shelf price.

Before you call

Where to find the model numberThe model number, the symptom in your own words, when it started, and what you have already tried.

By city

Dishwasher in Erie, PAThe same appliance, written for that market.

Questions people ask

What does dishwasher repair usually run?

It depends on which part failed, and that is not a dodge. The spread is real. The labor is much the same whether the part is cheap or expensive, so the part price is what separates a small bill from a big one. The useful question on the phone is which part we suspect and what it costs.

What should I have ready when I call?

Two minutes of getting ready changes how much we can tell you on the phone. Say what you already tried, resets and filter cleaning included, so nobody does it all twice. Write down what you already tried, then call.

Can an older dishwasher still be worth fixing?

If one part failed on a machine that has been fine until now, fix it. A motor, a pump, a water valve or a thermostat on a sound machine is usually the cheaper fix. A dead compressor or a cracked tub usually is not. Ask whether the part is still made before you decide either way.

Which appliance problems need attention first?

Urgency comes from the damage a fault is doing, not from how much it annoys you. A washer that will not drain is sitting full of water, so deal with it before the next load goes in. Lead with the water or the food when you call, not with the brand.

Is an appliance from the eighties or nineties still worth fixing?

Mechanical parts for old machines are still around. The electronics are the problem. Rebuilt and salvaged boards exist for some models, and they can keep a sound machine running. Get the model number and call before you write the machine off.

What makes one brand easier to repair than another?

Brand matters less than people expect, and parts supply matters more. Built in and panel ready units cost more in labor, because the machine has to come out before anyone can reach the parts. Read the model and serial off the sticker before you call.

Other appliances

The rest of what gets fixed

Get it diagnosed

Ask for the repair price before any work starts.

(716) 414-5233
Call (716) 414-5233